Home | Back Engineering to Index
Home | Back
Engineering to Index
Heat Requirement Calculations |
|
There are two basic heat energy requirements to be considered in the sizing of heaters for a particular application. |
|
| 1. Start-Up Heat
is the heat energy required to bring a process up to operating temperature. Start-up heat
requirement calculations which include a material change of state should be calculated in
three parts: 1) Heat requirement from ambient temperature to change of state temperature 2) Heat requirement during change of state (latent heat) 3) Heat requirement from change of state temperature to operating temperature |
2. Operating Heat
is the heat energy required to maintain the desired operating temperature through normal
work cycles. The larger of these two heat energy values will be the wattage required for
the application. A safety factor is usually added to allow for unknown or unexpected operating conditions. The safety factor is dependent on the accuracy of the wattage calculation. A figure of 10% is adequate for small systems closely calculated, while 20% additional wattage is more common, and figures of 25% to 35% should be considered for larger systems with many unknown conditions existing. |
| Start-Up Heat requirements will include one or more of the following seven (7) calculations, depending on the application. | |
| 1. Wattage required to heat material: | |
Weight of material (lbs) x Specific
Heat (Btu/lb °F) x Temperature rise (°F) |
= Watts |
| 2. Wattage required to heat container or tank: | |
Weight of container (lbs) x Specific
Heat (Btu/lb °F) x Temperature rise (°F) |
= Watts |
| 3. Wattage required to heat hardware in container: | |
Weight of hardware (lbs) x Specific
Heat (Btu/lb °F) x Temperature rise (°F) |
= Watts |
| 4. Wattage required to melt a solid to a liquid at constant temperature: | |
Heat of fusion (Btu/lb) x Weight
of material to be melted (lb/hr) |
= Watts |
| Heat of Fusion
(Latent Heat): The amount of heat required to change one pound of a given
substance from solid to liquid state without change in temperature is termed the heat of
fusion. It requires 144 Btu to change one pound of ice at 32°F to one pound of water at 32°F, the heat of fusion of ice being 144 Btu per pound. A change of state is usually accompanied by a change of specific heat. The specific heat of ice is 0.5; while that of water is 1.0. |
|
| 5. Wattage required to change a liquid to a vapor state at constant temperature. | |
Heat of vaporization (Btu/lb) x Weight
of material to be vaporized (lb/hr) |
= Watts |
| Heat of
Vaporization (Latent Heat): The amount of heat required to change one
pound of a given substance from liquid to vapor state without change in temperature is
termed the heat of vaporization. It requires 965 Btu to change one pound of water at 212°F to one pound of steam at 212°F. |
|
| 6. Wattage to counteract liquid surface losses: | |
Total liquid surface area (sq. ft.) x Loss
rate at final temperature (watts/sq. ft.) |
= Watts |
| 7. Wattage to counteract surface losses from container walls, platen surfaces, etc. | |
Total surface area (sq. ft.) x Loss
rate at final temperature (watts/sq. ft.) |
= Watts |
|
Operating heat
requirements will include one or more of the following four (4)
calculations. |
|
| 1. Wattage to counteract losses from open liquid surfaces. | |
Total liquid surface area (sq. ft.) x Loss rate at operating temperature (watts/sq. ft.) |
= Watts |
| 2. Wattage to counteract container or platen surface losses. | |
| Total surface area (sq. ft.) x Loss rate at operating temperature (watts/sq. ft.) | = Watts |
| 3. Wattage required to heat material
transferred in and out of the system. (Metal dipped in heated tanks, air flows, make-up liquids, etc.) |
|
Weight of material to be heated (lbs) x Specific
Heat (Btu/lb °F) x Temperature rise (°F) |
= Watts |
| 4. Heat-up of racks of containers, etc. transferred in and out of the system: | |
Weight of items to be heated (lbs) x Specific
Heat (Btu/lb °F) x Temperature rise (°F) |
= Watts |
|
Specific Heat: The heat necessary to increase the temperature of all other substances has been referred to water as a standard. The ratio of the amount of heat required to increase the temperature of one pound of any substance by one degree to the amount necessary to increase one pound of water is known as the specific heat of that substance. |